MOUSEDRV.TXT - MouseWare 6.43
(c) Copyright 1993-1994 Logitech, Inc.  All Rights Reserved
***************************************************************************
This file documents the MOUSEDRV.INI parameters and the DOS mouse driver
parameters.

To view or print this file under DOS, use README.EXE which is supplied on
the installation disks. At the DOS prompt type the following:

    README MOUSEDRV.TXT
***************************************************************************

TABLE OF CONTENTS

1. INI FILE STRUCTURE
   1.1  [Global] Section
   1.2  [COMx] Section
   1.3  [DOSGlobal] Section
   1.4  [Display] Section
   1.5  [WinGlobal] Section
   1.6  [DeviceType] Section
   1.7  [Technical] Section

2. DOS MOUSE DRIVER COMMAND LINE PARAMETERS
   2.1  Acceleration
   2.2  Button Mapping
   2.3  Button Swap
   2.4  COM Port
   2.5  Cursor Blinking Rate
   2.6  Cursor Lock
   2.7  Cursor Trail
   2.8  Device Type
   2.9  Drag Lock
   2.10 Mouse Speed
   2.11 Orientation
   2.12 Memory
   2.13 Miscellaneous

3. VESA Super VGA Support
   3.1  VESA Background
   3.2  VCI Background
   3.3  The Logitech DOS mouse driver and VCI Module
   3.4  Other Operating Environments/Systems
   3.5  Loading VCI Overlay Modules
   3.6  ROM Resident Overlay or TSR's
   3.7  Disabling VCI module loading

4. DOS Mouse Driver Memory Management
   4.1  DOS Memory Regions
   4.2  Cloaking Interface
   4.3  DOS Driver Memory Location
   
***************************************************************************
     
1.   INI FILE STRUCTURE

     MOUSEDRV.INI is a configuration file used by both the DOS and Windows
     drivers. This allows the mouse to have similar behavior under the two
     environments. Because the settings are stored in a file, the mouse
     settings will be the same from one boot session to another. To change
     the settings, use either the DOS or Windows Mouse Control Center.
     
     The format of MOUSEDRV.INI file is as follows:
     
          [section name]
          keyname=value
     
     The square brackets ([]) in the [section name] are required. Section
     names must start in the leftmost column. Within each sections are one
     or more "keyname=value" statements.
     
     Typically, a system has only one pointing device attached. Notebook
     users may have two pointing devices: a built-in trackball and a serial
     mouse. Others may use the DOS mouse driver in dual mode.
     
     For built-in trackball users, the mouse drivers will maintain two
     separate [DeviceType] sections. (Only one mouse may be in use at a
     time unless the DOS mouse driver is in dual mode.) The user will be
     able to maintain separate parameters for each device.
     
     When the DOS mouse driver is in dual mode, two [DeviceType] sections
     will be written. Parameters for the first mouse found will be used.
     
     Some parameters in the configuration file need to specify a particular
     button. This is designated as follows:
     
     100  Primary button
     010  Secondary button
     001  Third button
     
     These button values might be conbined to allow multiple buttons to be
     specified.
     
     For example:
     
          DragLock=011
     
     Assign the DragLock to the secondary and third buttons.
     
     
1.1  [Global] Section

     This section contains information common to both DOS and Windows mouse
     drivers.
     
     Connection=
        The hardware device type for the mouse that is currently
        connected. Only one device type will be listed. By default,
        Connection=None.
     
          BUS          Search for a BUS mouse
          Inport       Search for a Microsoft Inport mouse
          PS2          Search for a PS/2 mouse
          Serial       Search for a Serial mouse
     
     ConnectionPort=
        Current connection port used. By default, ConnectionPort=None.
     
          COM1         Serial COM port 1
          COM2         Serial COM port 2
          COM3         Serial COM port 3
          COM4         Serial COM port 4
     
     ForcedConnection=
        Determines if the mouse driver will use the 'Connection' and
        'ConnectionPort' parameters above to search for a mouse or use
        only the search order to find a mouse.
     
          On           Use Connection information to find a mouse
                       (default)
          Off          Perform a full search for mouse each launch time
                       using the search order given below.
     
     SearchOrder=
        Lists the order the driver uses to search for a mouse. The default
        search order is PS2, Serial, Bus, Inport.
     
          Bus          Search for a bus mouse
          Inport       Search for a Microsoft Inport mouse
          PS2          Search for a PS/2 mouse
          Serial       Search for a Serial mouse (M-series and C-series)
     
     PortSearchOrder=
        Lists the order the serial ports are searched. This is valid only
        for a Serial device. The default port search order is COM1, COM2.
     
     ActiveMouse=
        This parameter indicates which [DeviceType] section is used. The
        default is Unknown. Refer to the "[DeviceType] Section" in this
        document for a list of valid device types.
     
     
1.2  [COMx] Section

     This section defines the COM ports used by the computer. This section
     allows advanced users to configure their mouse for upper IRQ values
     and non-standard COM port address. The 'x' value must be filled in by
     the user as must the values in this section. Valid values for 'x' are
     1, 2, 3, and 4.
     
     Note: The COM port must be supported by the user's computer
     configuration. The mouse driver cannot configure the users COM ports.
     This value must match values that are used by the Windows PORTS
     Control Panel.
     
     BaseAddress=
        The base address of the COM port (given in hexadecimal). By
        default, the driver determines this value.
     
     IRQValue=
        The IRQ value of the COM port (given in decimal). By default, the
        driver determines this value.
     
     
1.3  [DOSGlobal] Section

     This section describes the settings used by the DOS mouse driver and
     DOS Mouse Control Center.
     
     BlinkingRate=
        Rate at which the DOS mouse cursor blinks. This setting is used
        only if the DOS mouse driver is loaded with cursor enhancements
        enabled.
     
          Fast         Sets text cursor to blink fast
          Slow         Sets text cursor to blink slow
          Off          Turns blinking off (default)
     
     CursorEnhancement=
        Indicates if the driver should load the cursor enhancements
        feature set.
     
          On           Load the cursor enhancements
          Off          Do not to load cursor enhancements (default)
     
     CursorLock=
        This locks the shape of the cursor in the DOS environment. This
        setting is used only if the DOS mouse driver is loaded with cursor
        enhancements enabled.
     
          On           Enables locking of the cursor shape
          Off          Disables locking of the cursor shape (default)
     
     CursorTrails=
        Enables or disables the cursor trails function. This setting is
        used only if the DOS mouse driver is loaded with the cursor
        enhancements enabled.
     
          On           Enables DOS cursor trails
          Off          Disables DOS cursor trails (default)
     
     CordlessReminder=
        The driver can check for the status of a cordless device when
        applications are launched. Depending on the device, the status can
        include information about the battery level or the interference of
        two or more cordless devices. This checking can be disabled if the
        status check is too time consuming or if it takes to much memory
        space. It is recommended to leave this setting enabled.
          On           Enable the cordless mouse reminder (default)
          Off          Do not install the cordless reminder
          
     DriverVersion=
        The DOS driver version number for this release.
       
     Memory=
        The memory allocation strategy the driver will use to relocate
        itself. The default setting will allow the driver to look for the
        best location available in memory. The driver will try to relocate
        itself first in extended memory, next in upper memory and finally
        in conventional memory. This default behavior can be overriden
        with the value below. In case an option cannot be satisfied, the
        next lower allocation strategy will be used.
     
          Automatic    Load in the best memory available (Default)
          Upper        Load in upper memory
          Conventional Load in conventional memory
          
     MemoryStub=
        When the driver runs in extended memory, it still needs to
        maintain a stub of about 1K in conventional or upper memory.
     
          Automatic    Load the stub in upper memory (Default)
          Conventional Load the stub in conventional memory
       
1.4 [Display] Section
       
     UseVCIOverlay=
        The driver can use an external video overlay instead of its built-
        in video code. This flag will enable or disable the search for
        such a module.
          
          On           Attempt to load the video overlay specified in the
                       VideoModule keyname.
          Off          Use the mouse driver built-in video code. (Default)
     
     VideoModule=
        Location of the VESA VCI video cursor overlay. This value is
        either a file name, the keyword RESIDENT, or blank for no VCI
        support. If only a file name is present, the driver will assume
        that the VCI file is located in the driver directory. By default,
        the directory where MOUSEDRV.INI is located is used. If the
        overlay cannot be found or has an incorrect format, the driver
        will revert to its internal video code.
     
1.5  [WinGlobal] Section

     The section describes the settings used by the Windows mouse driver.

     UseDOSDriver=
        This parameter must be used with caution and might help to solve
        some compatibility problems. If you experience serious troubles
        with the Windows mouse driver, you can still use your mouse (with
        limited functionality) under Windows through the use of the DOS
        mouse driver. When you set this parameter to On, make sure you've
        got the DOS mouse driver launched before you start Windows.
     
          On           Use the DOS mouse driver under Windows. The mouse
                       functionality will then be limited.
          Off          Normal use of the Windows mouse driver (default)

     DriverVersion=
        Windows mouse driver version number.
     
     WinCC=
        The full path and file name of the Windows Control Center. The
        default directory is same as the location of the Windows mouse
        driver LMOUSE.DRV.
     
     
1.6  [DeviceType] Section

     Each connected device will have its own section defining that device's
     characteristics. The 'DeviceType' name will be a text string
     describing the mouse model as follows. Values written here are for
     mice that can identify themselves (e.g. MouseMan) or for general
     groups of mice (e.g. SerialM). For unidentifiable mice, the
     'DeviceModel' parameter may be used to specify a device shape. By
     default, the DeviceModel name will be the same as the DeviceType.
     
     Note for DOS dual mode: Only one device's [DeviceType] section will be
     supported at a time. For dual mode, the DOS mouse driver will write
     out the second mouse's [DeviceType] section but will not use it. Only
     the first mouse found section will be used. To indicate the active
     device section, the parameter 'ActiveMouse' will be used. Please see
     ActiveMouse description in the [Global] section.
     
     The device types are:
     
       Bus                 Bus mouse
       Inport              Microsoft Inport mouse
       PS2                 Non-identifiable PS/2 type mice
       SerialC             C7, C9, TrackMan I, etc. (Non-identifiable C-
                            Series type mice)
       SerialM             Kidz mouse, Microsoft mouse, etc. (Non-
                            identifiable M-type mice)
       SerialV             MouseMan Serial, First mouse, etc. (Non-
                            identifiable V-type mice)
       MouseMan            MouseMan mice (W-type, W-type lefty, A-type)
       MouseMan2           MouseMan mice (PnP/A-type, new shape)
       TrackMan2           TrackMan II stationary mouse (W-type)
       TrackMan3           TrackMan II stationary mouse (A-type)
       TrackManPortable1   TrackMan Portable (W-type)
       TrackManPortable2   TrackMan Portable (A-type)
       TrackManVoyager     TrackMan Voyager (A-type)
       Cordless1           MouseMan Cordless (original cordless mouse)
       Cordless2           MouseMan Cordless (second generation cordless
                            mouse)
       Cordless3           MouseMan Cordless (PnP/A-type, new receiver)
       IntegratedTrackBall1Integrated trackball
       OS2Mouse            Windows driver only: for use under WINOS2, OS2
                            2.X
     
     Acceleration=
        The acceleration setting for the mouse drivers.
     
          Low          Low acceleration setting (default)
          Medium       Medium acceleration setting
          High         High acceleration setting
          Off          Disable acceleration
     
     
     BaudRate=
        This parameter sets the baud rate for the mouse. Values of 1200
        and 9600 are valid for M series type 'W' mice. All values are
        valid for C series mice.
     
          1200         Mouse is communicating at 1200 baud
          2400         Mouse is communicating at 2400 baud
          4800         Mouse is communicating at 4800 baud
          9600         Mouse is communicating at 9600 baud
     
        The default value varies according to mouse type:
     
            C Series = 2400
            M Series = 1200
            Cordless = 9600
     
     ChannelNumber=
        Identifies the channel number on which the cordless mouse is
        communicating. Available channels are 1 through 8 for original
        cordless mice, and 1 through 4 for new cordless mice. This value
        is provided for information only. The default value is 4.
     
     DeviceModel=
        A text string that identifies mice that do not have identification
        sending ability. This command will allow the Windows Control
        Center to display pictures of unidentifiable mice. This parameter
        will be entered either by the end user or through the installation
        program. By default, the DeviceModel name will be the same as the
        DeviceType.
     
          C7           Logitech C7 three button square mice
          C9           Logitech Series 9 three button mice
          TrackMan1    Logitech TrackMan I stationary mouse
          Kidz         Logitech Kidz mouse
          Microsoft1   Old Microsoft mouse
          Microsoft2   Square Microsoft mouse
          Microsoft3   New Microsoft mouse
          FirstMouse   Logitech First mouse
          PilotMouse   Logitech Pilot mouse
          MouseManLeft1Logitech original left-handed MouseMan
     
     NumberOfButtons=
        This parameter identifies the number of buttons a mouse has. It is
        used for mice that cannot identify the number of buttons they have
        (such as Inport mice). The default is 3 buttons.
     
     Orientation=
        Degree setting from 0 to 359. The default is 0 degrees.
     
     MouseSpeed=
        Mouse sensitivity value ranging from 1 to 100. The default is 50.
     
     DragLock=
        Drag lock is defined for the primary button only. The button value
        will indicate the buttons currently acting as a drag lock source.
        For example DragLock=011 sets the draglock function for the
        secondary and third buttons.
     
     MappingButtonX=
        The 'X' will be replaced by a physical button number. This give
        the correspondance between a physical button and a logical button.
        For example MappingButton2=010 means that the physical button
        number two on the mouse generates a logical secondary button.
     
     ChordDelay=
        Chording delay for 2 button devices. The value ranges from 0 to
        100. The larger the value, the more time the driver will wait for
        a chording. The null value effectively disables the chording
        functionality.
     
     Disabler=
        Decimal value representing the shift, control or alt keys on the
        keyboard that will disable the macro function assigned to a
        logical button.

1.7  [Technical] Section

     This section describes technical settings used by the mouse drivers.
     These settings might help to solve compatibility problems with certain
     type of hardware or BIOS.
     
     ForcePS2EquipmentFlag=
        Indicates if the driver should force the detection of a PS2 mouse.
     
          On           Simulate a PS2 mouse found during boot time.
          Off          The flag is set by the BIOS during boot
                       time.(default)
     
     Timing=
        Indicates which timing procedures the driver should use.
     
          Software     Use software loops to compute timing (default)
          Hardware     Use the PC timer chip to compute timing
     
     DetectIPDevice=
        Indicates if the driver should use the BIOS integrated pointing
        device interface to identify a device.
     
          On           Use the BIOS interface.
          Off          Ignore the BIOS interface (default)
          
     DebugTiming=
        Technical support flag. Do not change.
     
          On           Allow special timing specification
          Off          Use normal timing (default)
     
2.   DOS MOUSE DRIVER PARAMETERS

     The DOS mouse driver has the ability to read parameters from the
     command line. This section lists the valid parameters.
     
     The syntax for the command line is:
     
         MOUSE [Option1], [Option2], ...
     
     For example:
     
         MOUSE SWAP S07
     
     will SWAP the mouse buttons and set a slightly above medium
     sensitivity.
          
2.1  Acceleration

     With Acceleration, you can make the mouse more or less sensitive to
     movement relative to the speed with which you move the mouse. By
     moving the mouse quickly, you can sweep the cursor across your screen
     with very little mouse movement. Likewise, by moving the mouse slowly
     you can zero in on an exact screen position.
     
          AOFF         Turns acceleration off
          ALOW         Sets acceleration to low
          AMEDIUM      Sets acceleration to medium
          AHIGH        Sets acceleration to high
          
          
2.2  Button Mapping
     
     The 1K and 3K options set the mapping of the physical mouse buttons.
     The default is 3K and will map the physical buttons to their default
     logical mapping. The 1K option will map all the buttons to the primary
     button. To revert to the default button mapping, use the 3K option.
     
2.3  Button Swap
     
     Use the Button Swap option to logically swap the function of the mouse
     buttons.
     
          SWAP         Swaps two predifined mouse buttons
     
     On regular mice and trackballs, the predifined buttons are the
     physical left and right buttons.
     On the TrackMan Portable the buttons are the bottom and middle
     buttons.
     
2.4  COM Port
     
     This setting forces the driver to look for the serial mouse on either
     COM1 or COM2. If not found, the driver will search for all the other
     attached mice.
     
          1            Serial COM port 1
          2            Serial COM port 2
     
     
2.5  Cursor Blinking Rate

     This setting determines how fast the cursor blinks. This option is
     only available if the mouse driver was loaded with cursor
     enhancements.
     
          COFF         Turns off the cursor blinking rate
          CSLOW        Sets the cursor blinking rate to slow
          CFAST        Sets the cursor blinking rate to fast
     
     
2.6  Cursor Lock

     This locks the shape of the cursor in the DOS environment. This option
     is only available if the mouse driver was loaded with cursor
     enhancements.
     
          DCURSOR      Sets the default mouse cursor
          LCURSOR      Locks the mouse cursor shape
     
     
2.7  Cursor Trail

     This flag sets the mouse trail either on or off. The mouse trail is
     useful on laptop/notebook computers where the cursor is sometimes
     difficult to find. This option is only available if the mouse driver
     was loaded with cursor enhancements.
     
          TON          Turns on the mouse trail for text video modes
          TOFF         Turns off the mouse trail
     
     
2.8  Device Type
     
     This setting allows you to force the mouse driver to look for the type
     of mouse attached. If the device is not found, it will search for the
     other types.
     
          BUS          Search for a bus mouse
          SER          Search for a serial mouse
          INP          Search for a Microsoft Inport mouse
          PS2          Search for a PS/2 mouse
     
     
2.9  Drag Lock

     Drag lock lets you drag an object without having to hold down a mouse
     button as you move the mouse. When you click the mouse button assigned
     to Drag Lock, the driver interprets this as though you were pressing
     and holding down the left mouse button. Simply moving your mouse
     performs the drag. To end the drag, click the assigned mouse button
     again.
     
          DMIDDLE      Sets the drag lock function to the middle button.
                       This drags the left (primary) button.
          DRIGHT       Sets the drag lock function to the right button.
                       This drags the left (primary) button.
          DBOTH        Sets the drag lock function to both the middle and
                       right buttons. This drags the left (primary)
                       button.
          DNONE        Disables the mouse drag lock effect.
     
     
2.10 Mouse Speed

     You can make the mouse move faster or slower relative to the distance
     in which you move your mouse. By setting the speed very fast (e.g.
     S10), you can move your mouse a very small distance to sweep the mouse
     cursor from one side of the screen to the other. A slow speed setting
     (e.g. S01) requires that you move the mouse a greater distance to
     sweep the cursor from one side of the screen to the other.
     
          S00 - S10    Values range from S00 (slow) to S10 (fast)
     
     
2.11 Orientation

     This option is useful for the TrackMan Portable. Orientation sets the
     direction to which the mouse ball must be moved in order to move the
     mouse cursor in a given direction on the screen. The valid angles are
     from 0 to 359 degrees in one degree steps (Default: 0).
     
          ORIENT=0-359
     
          0            Sets the orientation to north (default). This
                       setting is mainly used by right-handed people.
                       Rolling the track ball away from you moves the
                       cursor up.
          180          Sets the orientation to south. This setting is
                       mainly used by left-handed people. Rolling the
                       track ball away from you moves the cursor up.
          90           Sets the orientation to west. This setting can be
                       used by both left- and right-handed people. Rolling
                       the track ball up moves the cursor up.
          270          Sets the orientation to east. Though supported,
                       this option is not useful for the TrackMan
                       Portable.
     
2.12 Memory
     The memory options allow to specify where in memory the driver will be
     resident. The options related to the stub are applicable only when the
     driver is loaded in extended memory.

          MEMU         Place the driver in upper memory if possible
          MEMC         Place the driver in conventional memory

     
2.13 Miscellaneous

     The following lists the miscellaneous options available to the mouse
     driver.
     
          ?            Displays the mouse configuration information
          /?           Display the list of options
          INIT         Resets the mouse to the factory default settings
          NOINI        Loads the driver without using the MOUSEDRV.INI
                       file settings. The driver default settings will be
                       used.
          NOVCI        Loads the driver without Super VGA support.
                       (Default)
          VCI          Enable loading of an external video module
          OUT          Removes the mouse driver from memory
          CENHANCE     Loads the mouse driver with cursor enhancement
          NOCENHANCE   Loads the mouse driver without cursor enhancement
          
3.   VESA Super VGA Support

3.1  VESA Background

     The VGA standard was established by IBM to define a video architecture
     and video mode. Super VGA is loosely defined as anything above the VGA
     standard. This includes higher resolutions (e.g. 800 x 600 for VESA
     mode 100h) and greater or equal number of colors (e.g. 256 colors for
     VESA mode 103h).
     
     While many video manufacturers follow the VGA standard, some add their
     own custom enhancements. VESA (Video Electronics Standard Association)
     was formed to bring together the different video schemes, and to give
     direction to the future of video standards for the IBM personal
     computer.
     
     
3.2  VCI Background

     Under DOS, many applications require the mouse driver to draw the
     mouse cursor. To do this, the mouse driver must have knowledge of the
     underlying video architecture and video mode being displayed. This
     present problems as video boards surpass the VGA limit. As video
     boards become more complex the mouse driver must be expanded to handle
     all situations.
     
     To remedy this, both VESA and Logitech Inc. have established the Video
     Cursor Interface (VCI) Standard. This standard outlines the interface
     between an input device, such as a mouse, and a small overlay program
     containing hardware dependent cursor movement and drawing code. The
     host (or mouse driver in this case) calls the VCI module to perform
     all cursor functions. The host need not have any knowledge of the
     cursor drawing software/hardware.
     
     The VCI module can be implemented in one of three forms:
     
     - as an overlay program that the host program loads,
     - as a TSR/device driver program that redirects INT 10h to itself,
     - as a ROM resident code.
     

3.3  The Logitech DOS mouse driver and VCI Module

     The Logitech mouse driver contains video cursor support for CGA, EGA,
     VGA and VESA Super VGA video modes version 1.1. Although this code
     will work with all these video modes, video manufacturers might
     provide a VCI module to take advantage of special features in their
     hardware.

     During initialization, the MOUSE driver will search MOUSEDRV.INI for
     the location of a VCI module if the UseVCIOverlay is enabled. Refer to
     Section 1 for more information on MOUSEDRV.INI. If an overlay file is
     specified, the mouse driver loads it into memory, then calls the VCI
     module initialization routine. If initialization is successful, the
     overlay code is copied into the mouse driver, becoming part of the
     resident mouse driver. If initialization fails, the mouse driver uses
     it's default video cursor code.
     
     
3.4  Other Operating Environments/Systems
     
     Under other operating environments (Windows, GEM) and operating
     systems (OS/2, UNIX) the mouse driver is not required to display the
     cursor on the video screen. The mouse driver simply acquires button
     and movement information and passes it to the operating
     environment/system which does the rest of the work. The VCI does not
     apply to such operating environments/systems.
     
     
3.5  Loading VCI Overlay Modules

     To change the overlay file being used, edit MOUSEDRV.INI as follows:
     
          [Display]
          VideoModule=DRIVE:PATH\NEW_OVL.OVL
     
     where NEW_OVL.OVL is the name of the new overlay program. The
     DRIVE:PATH are needed if the overlay is not located in the mouse
     driver's directory.
     
     
3.6  ROM Resident Overlay or TSR's
     
     Some video manufacturers may put their video overlay code in the ROM
     BIOS or in a TSR (Terminate and Stay Resident) program. The video
     manufacturer should provide information to the user about this. To
     enable the mouse driver to search for a BIOS VCI implementation or
     TSR, edit MOUSEDRV.INI as follows:
     
          [Display]
          VideoModule=RESIDENT
     
     This tells the mouse driver to search for the video overlay that is
     already present in memory.
     
     
3.7  Disabling VCI module loading

     To disable the usage of a VCI overlay, edit MOUSEDRV.INI. Either
     remove the filename:
     
          [Display]
          VideoModule=
     
     or set the UseVCIOverlay keyname to disabled:
     
          [Display]
          UseVCIOverlay=Off
          VideoModule=VCI.OVL
     
     Alternatively, on the first call to the DOS mouse driver, type:
     
          MOUSE NOVCI
     
     NOVCI forces the mouse driver to use it's internal video code.
     
4.   DOS Mouse Driver Memory Management

4.1  DOS Memory Regions
     
     The DOS operating system and the PC architecture sudivided the memory
     available on a computer in different regions. These regions are:
     
     Conventional Memory:
     Conventional memory is the first 640K of memory. This is the memory
     that all DOS applications use.
     
     Upper Memory Block (UMB):
     The upper memory area was originally defined as a region reserved for
     system hardware like the video or hard-disk controllers. With the
     advent of memory managers, unused portions of this area are available
     for storing DOS device drivers and TSR. It contains a maximum of 384K
     of memory.
     
     High Memory Area (HMA):
     The high memory area is the first 64K of extended memory. The
     himem.sys or third-party memory managers are often used by DOS to
     access this part of the memory. This is where DOS is often stored.
     
     Extended Memory:
     Extended memory is any region above one megabyte. DOS is unable to use
     this memory without the use of an additional memory manager. This
     memory is often used by programs to store data.
     
     As DOS applications have increased in sophistication, they have also
     increased in size. Since all DOS applications must run, at least in
     part, in conventional memory, it is desirable that as much
     conventional memory as possible be kept free. On today's systems, with
     the software needed to run their sound cards, mice and other
     peripherals, this is increasingly difficult. The adroit user will
     place the software for these devices in upper memory, but this area
     has also become increasingly crowded. Abetting this so called "ram
     cram" is the design goal of the DOS mouse driver memory management.
     
4.2  Cloaking Interface is not included on this general update disk. 
     It is included on the Retail Release of MouseWare 6.50 and can 
     be ordered by calling Logitech Customer Service at 1-800-231-7717.
     
4.3  DOS Driver Memory Location
     
     By default, the DOS mouse driver will load in the best location
     possible in memory. The driver checks for available
     space in the upper memory blocks and relocates itself there.
     Otherwise, the driver will stay in conventional memory.
     
-------------------------------------------------------------------------
End of file MOUSEDRV.TXT
-------------------------------------------------------------------------
